Pneumatic Semi-Automatic Glue Dispenser Machine with Timer Control - Manual & Auto Liquid Solder Dispensing Controller for Precision Glue Dropping | Ideal for Electronics Assembly, DIY Crafts, and Small-Scale Manufacturing

SpecificationColor: BlackModel: 982Material: MetalSpitting Mode: Manual / Semi-automaticMinimum Drip Volume: 0.01mlSpitting Time Interval: 0.1-9.9sAutomatic Timing(Can Be Set): 0.01-30s Repeat Accuracy: ±0.5%Internal Voltage: 12-24DCInput Air Pressure: 2.5-7bar(35-100psi)Output Air Pressure: 0.1-5.5bar(1-78psi)Power Supply: 110V AC, 60Hz Power Consumption: 20WPlug Specification: American Standard 110VProduct Size:23*15*6cm/9.05*5.9*2.36inPackage Size:20*26*14cm/10*9*12.5inGross Weight: 2.1kg/4.63 lbsNotes: 1. The input high pressure should not exceed 7 bar (100psi), and the maximum working pressure of the glue dropper should not exceed 5.5 bar (78psi). If the working air pressure is above 4 bar, please switch to aluminum connectors.2. If available, store all materials at a constant temperature (5°) as directed to ensure that the concentration does not change significantly during use.3. When the material concentration is too large (flow difficulties), can not drip, if you want to use it, according to the manufacturer's instructions dilute the use; before work, the material must be fully stirred evenly to ensure that the size of the drip consistent.4. Automatic state, the general air pressure adjustment in the machine at 1-2.7bar (15-40psi) is more appropriate. When working in the automatic state, the strength of the vacuum tube pumping back air should be adjusted to the proper position. Too much pumping back will flush the piston and destroy the normal operation. 5. Automatic state work, according to the actual situation, timely removal of the material left at the needle nozzle, these materials gradually curing will block the muzzle discharge and back pumping; after work, the barrel should be cleaned in time, otherwise, the barrel's disassembly will be very difficult.6. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement and make sure you do not mind before ordering.

【Semi-automatic Glue Dispenser】Our semi-automatic glue dispenser machine can precisely control the dripping speed and improve the working efficiency! No matter whether the semi-automatic mode or manual operation, both need to pedal the foot switch at the same time. Minimum Drip Volume 0.01ml,Spitting Time Interval 0.1-9.9s,Automatic Timing(Can Be Set) 0.01-30s,Repeat Accuracy ±0.5%,Input Air Pressure 2.5-7bar(35-100psi),Output Air Pressure 0.1-5.5bar(1-78psi)

【Professional Glue Dispenser Machine】This pneumatic dispensing controller adopts a high-quality electronic valve with a certain anti-impregnation function, to better ensure operational safety and can also effectively extend the life of the semi-automatic glue dispenser machine, which can instantly start the diaphragm valve and increase the working efficiency by more than 80%. High-precision air pressure gauge can precisely control the air pressure input to the air pump and convert the air pressure precisely to ensure that the air tube will not break

【Vacuum Back Suction】This semi-automatic glue dispenser machine is equipped with a vacuum back suction device, which can effectively prevent the glue from dripping during use to achieve a more accurate glue dripping, and ensure a clean and tidy working environment

【Stable Performance】 Features a high-end all-copper coil transformer, which can stabilize the voltage change and increase the service life, and can be used in high-frequency and high-intensity work scenarios, improving operational safety while being efficient and energy-saving. Also uses the fourth generation chip design circuit board, significantly improving stability

【Wide Applictaions】Suitable for most of the yellow glue, quick-drying glue, epoxy resin, etc. in the market, and is widely used in bonding various electronic components, machine production, instrumentation, jewelry, and other objects

【Complete Set】1x Dispenser Main Unit,1x Manually Switch,1x Foot Switch,1x Air Tube,1x Connection Tube,1x Power Cord,1xDispenser Stand,2x 30CC Liquid Barrels,6x Dispensing Needles,1x Instruction Manual